Graco 257129 Gun Filter 30 Mesh
$12.60
In Stock
The Graco 257129 Gun Filter (30 Mesh) is a genuine in-gun filter designed to keep debris out of your spray tip for smoother, clog-free spraying. Ideal for medium to heavy coatings.
- Part No.: 257129
- Mesh: 30 (coarse for thicker materials)
- Fits: Contractor, Contractor II, Contractor PC, FTx, FTx II Guns
- Use With: Heavier latex, primers, elastomerics
- Purpose: Prevents tip clogging and improves finish quality
Quantity
Genuine OEM Part
Fast Shipping (Order by 1 PM CST)
Easy Returns
Compatible Machines & Guns – Graco 257129 Gun Filter (30 Mesh)
Compatible Graco Spray Guns (and the sprayers that use them)
This 30 mesh gun filter fits the Graco guns below. If your sprayer uses one of these guns, this filter will fit.
- Contractor / Contractor II Airless Spray Guns (e.g., 246220, 246221, 246434)
- FTx / FTx II Airless Spray Guns (e.g., 246230, 246231, 246435)
- New Contractor Series Guns (e.g., 288420, 288421, 288425)
- New FTx Series Guns (e.g., 288429, 288430, 288431)
- Contractor PC Guns (select models that specify 30-mesh filters)
What is the Graco 257129 30 Mesh Gun Filter?
The 257129 is a genuine Graco gun filter with a 30 mesh screen. It installs inside the spray gun handle to capture larger particles before they reach the tip—helping reduce tip clogs, maintain a consistent spray pattern, and prolong gun/tip life.
At-a-Glance Specs
| Part Number | 257129 |
|---|---|
| Type | Gun Filter / In-handle screen |
| Mesh | 30 Mesh (coarser screen for heavier coatings) |
| Quantity | Typically 1 per card (check listing) |
| Primary Fit | Contractor, Contractor II, Contractor PC, FTx, FTx II guns (see list above) |
| Typical Use | Heavier latex, primers, elastomerics, block fillers (when 30-mesh is specified) |
Key Benefits
- Helps prevent tip plugging by catching debris before the tip
- Supports a more consistent spray pattern and finish quality
- Protects the gun & tip—less downtime and maintenance
- Right-size 30 mesh for many medium-to-heavy coatings (when recommended)
Choosing the Right Mesh
Use the mesh size your gun/sprayer manual recommends for the coating:
- 30 Mesh – Coarser; for heavier paints/primers & thicker materials
- 60–100 Mesh – Medium/finer; for most acrylics/enamels (as specified)
- 200 Mesh – Very fine; select finishes (as specified)
Maintenance Tips
- Clean the filter after each use; replace if damaged, deformed, or persistently clogged
- Match mesh to coating to avoid flow restriction or poor filtration
- Flush and strain coatings to maximize filter life and finish quality
Frequently Asked Questions
It fits the spray gun (installed inside the handle). If your sprayer ships with or is paired to a Contractor, Contractor II, Contractor PC, FTx, or FTx II gun that specifies 30 mesh, then 257129 is the correct in-gun filter. Always confirm your exact gun model.
30 mesh is coarser and is often used for heavier coatings (heavier latex, primers, elastomerics) when recommended. Many standard architectural paints may specify 60–100 mesh. Follow your coating data sheet and gun/sprayer manual.
Inspect and clean after each use. Replace when dented, torn, deformed, or if clogs persist even after proper cleaning and flushing. Keeping spare filters on hand minimizes downtime.
Yes. Too fine a mesh can restrict flow and cause poor atomization; too coarse may allow debris to pass and plug the tip. Use the mesh specified for your coating and equipment.
No. 257129 is an in-gun filter. Manifold/pump filters are separate components on the sprayer and use different part numbers and mesh ranges.
No reviews yet. Be the first to review this product!
