.png)
Graco RentalPro 210PC Electric Airless Sprayer Parts (2) Power Up Your Projects with Genuine OEM Components
Graco® RentalPro 210PC is the go-to electric airless sprayer for tool-rental yards and remodelers who need reliable performance day after day. Its PowerStroke™ DC motor, rated to deliver a steady 0.47 GPM at up to 3000 PSI, pushes latex, acrylics and elastomerics through tips as large as 0.021 in without a hiccup. But a sprayer only stays productive when the seal kits, suction sets and filters inside it are factory fresh and built to the same thousandth-of-an-inch tolerances Graco engineers into every new machine. That’s why SprayersAndParts stocks every OEM-sealed component—so you can spec, source and ship rental-grade parts in one friction-free stop.
Why Choose Genuine Graco RentalPro 210PC Parts?
- Exact tolerances. Chromex-plated piston rods finished to 0.0005 in keep packings alive for 300+ gallons.
- Chemical confidence. Viton® and UHMWPE elastomers handle hot solvents that melt bargain Buna seals.
- Warranty protected. Only OEM parts preserve Graco’s one-year pump and motor coverage
- Rapid ROI. Longer service intervals and shorter change-outs mean more billable spray hours per week.
Dive Into the Pump Breakdown
pump section contains the piston, cylinder and packings that do the heavy lifting on every trigger pull. Swap the full wet-end in under five minutes using Graco’s ProConnect™ two-bolt mount—no pin punches, no fighting spring retainers. Install the complete 288514 Repair Kit every 250 hours or sooner if your pressure drops more than 10 % at constant RPM. A laminated Graco sprayer parts diagram comes with each kit so even first-time techs seat the V-packings and carbide seats in the proper order.
Key Specifications & Performance
| Max Working Pressure | 3000 PSI / 207 bar |
|---|---|
| Free-Flow Delivery | 0.47 GPM / 1.8 L min-1 |
| Motor Output | 7⁄8 HP Permanent-Magnet DC |
| Supported Tip Size | Up to 0.021 in (1 gun) |
| Fluid Section | Endurance™ Chromex rod, stainless cylinder |
| Weight (dry) | 58 lb / 26 kg |
| Power Requirement | 120 V, 15 A circuit |
Top-Moving Parts in Stock & Ready to Ship
- 288514 Pump Repair Kit. Complete piston, packings and seats—restores full pressure fast.
- 17Y297 Prime/Spray Valve. Brass body, Viton seat; solves 80 % of “won’t prime” calls.
- 17P186 FlexLiner Adaptor. Lets you use graco truecoat 360 accessories cups on small-volume jobs.
- 246384 50-ft Graco hose. 3300 PSI-rated, spring guards both ends—lighter than generic rubber.
- Graco gun repair kit 287030 for SG3, SG20 and SG Pro guns.
- Easy-out filters & strainers (60-, 100- and 200-mesh) to match every coating viscosity.
Cross-Compatibility with Other Graco Gear
Running a TrueCoat handheld for cabinet touch-ups? graco spray gun accessories—RAC IV tips, tip guards and 60-mesh manifold filters—transfer straight to the RentalPro 210PC. Need extra reach on vaulted ceilings? Clip a 30-in graco hose whip between the gun and main line to cut operator fatigue without starving flow. Even drywall skimming blades integrate: dial the pressure to 300 PSI, swap to a 122-degree fan tip, and back-roll joint compound for glass-flat Level 5 walls.
Maintenance Blueprint for 1,000-Hour Pump Life
After Every Use – Flush with the coating’s recommended solvent until clear, then run Pump Armor® to protect packings.
Every 50 Hours – Grease throat packing with TSL™, inspect inlet screen; replace if 20 % of mesh is blinded.
Every 250 Hours – Install a new pump kit, torque piston nut to 55 in-lb, log total gallons sprayed in your digital maintenance app.
Annually – Replace the drive belt, pressure-test to 2500 PSI for 60 seconds, verify the digital hour meter accuracy.
Pro Tips from SprayersAndParts Desk
- Color-code bins—blue for guns, red for pumps, yellow for tips—cuts pick errors in half.
- Zip-tie tips together by orifice (515, 517, 619) for lightning-fast grabs when paint is flashing.
- Store a spare suction set & graco filters and strainers in a sealed poly bag; dried latex flakes destroy packings.
- Use a torque-limiting ratchet when installing the pump kit—over-tightened seats chip under 3000-PSI shocks.
Frequently Asked Questions
- Will an X5 hose fit the RentalPro 210PC?
- Yes—both use 1⁄4-in NPSM threads and are rated 3000 PSI.
- Can I spray oil-based enamels with the factory packings?
- Absolutely. Viton and UHMWPE elastomers resist most solvents. Flush thoroughly with mineral spirits after spraying.
- How often should I change filters?
- Swap manifold and gun filters every 10 gallons on latex, every 5 on texture—cheap insurance against tip clogs.
Ready to Keep Your RentalPro 210PC Earning?
From money-saving graco filters and strainers to time-saving graco hose whips and graco gun repair kits, SprayersAndParts has the OEM components you need to stay profitable and on schedule. Load your cart now, choose your ship speed and experience the difference tomorrow.