Please wait while we process your order...

Free Shipping on Qualifying Orders Fast Shipping — Most Orders Ship Same Business DayOrder by 1 PM CST for fastest dispatchCall +1 713-931-4102
Link copied!

How to Run a Stall Test on a Graco Airless Sprayer

November 17, 2026 • 11 min read
Quick Answer

To run a stall test, prime the sprayer, turn the valve to SPRAY, bring it up to pressure, trigger the gun to clear the air, then release the trigger and wait. A healthy sprayer stalls: the motor stops and does not restart until you pull the trigger again. If it restarts by itself, pressure is leaking past the prime valve, a check valve, the packings or an outside fitting. Graco's maintenance table for its contractor sprayers says to check stall every 1000 gallons.

Difficulty: Easy Time: 5 minutes Tools: Pail of water, empty cup, flashlight Parts: None for the test
Key Takeaways
  • Stall means the motor stops when the gun is closed and stays stopped. That is normal and healthy.
  • A sprayer that restarts on its own has a leak. Where the leak goes tells you which part to fix.
  • Check the drain tube first. A leaking prime valve is the cheapest cause and the easiest to see.
  • Low stall pressure is a different result. It points to the pressure control, not the pump.

Painters tend to judge a sprayer by the fan. If the pattern looks good, the machine is good. The trouble is that a pump can lose a good deal of its efficiency before the fan shows it, because the motor simply runs longer to make up the difference. By the time the pattern tails, the wear is well advanced.

The stall test finds that wear early. It asks one question: when nothing is being sprayed, does the pump hold its pressure? The answer takes five minutes to get, and Graco includes the check in its maintenance schedule.

1. What Stalling Means

An airless sprayer does not run all the time. The control watches the pressure. When pressure reaches the setting, it stops the motor. When you pull the trigger and pressure falls, it starts the motor again.

Graco's maintenance table for the 490 to 650 PC sprayers describes the check in two sentences. With the gun not triggered, the motor should stall and not restart until the gun is triggered again. If the sprayer starts again with the gun not triggered, inspect the pump for internal and external leaks and check the prime valve for leaks.

So there are two things a stall test can show you.

  • The sprayer will not stay stalled. Pressure is escaping somewhere.
  • The sprayer stalls too early. The control stops the motor before full pressure is reached.

2. Running the Test

Use water. It is thinner than paint, so it finds a leak that paint might hide, and it costs nothing.

  1. Prime the sprayer

    Put the suction tube and the drain tube in a pail of clean water. With the prime valve down, run the pump until the stream from the drain tube is steady and free of bubbles.

  2. Turn the valve to SPRAY

    Close the prime valve so the pump feeds the hose.

  3. Bring the pressure up

    Turn the pressure control up to a normal working setting. For a check of maximum pressure, turn it fully clockwise.

  4. Clear the air

    Remove the tip, or turn it to the unclog position, and trigger the gun into the pail until the flow is solid. Air in the hose gives a false result.

  5. Release the trigger and lock it

    Let go and set the trigger lock. The motor should run for a moment and stop.

  6. Wait and listen for two minutes

    Do not touch the gun. Count how often the motor restarts, if it does at all.

  7. Check the drain tube

    Hold the end of the drain tube over an empty cup while you wait.

  8. Look for outside leaks

    Run a flashlight over the hose couplings, the gun, the filter cap, the pump's packing nut and the fittings.

Treat it as a live sprayer

The system is at full pressure throughout this test. Keep the trigger lock on, keep your hands away from fittings and never feel for a leak with your fingers. Fluid at spraying pressure can inject through skin. When you have finished, switch off and relieve pressure before you loosen anything.

3. Reading the Result

The motor stops and stays stopped for two minutes

No restarts, a dry drain tube, no drips.

Result: pass. The pump, the valves and the prime valve are all holding.

The motor restarts and the drain tube is wet

Water collects in the cup with the valve on SPRAY.

Result: the prime valve is leaking. Clean or replace it. See how to replace a Graco prime valve.

The motor restarts and there is a drip outside

A wet coupling, a dripping gun or a weeping filter cap.

Result: an external leak. Tighten or reseal the connection. A dripping gun needs a needle kit.

The motor restarts, the tube is dry and nothing drips

It cycles every few seconds with no visible reason.

Result: an internal leak in the pump. The intake valve, the piston valve or the piston packings.

The motor stops early and the fan has tails

With the control fully clockwise, the sprayer stalls short of full pressure.

Result: low stall pressure. The pressure control is at fault, not the pump.

How often is too often

A sprayer in good order does not restart at all during the test. One restart in two minutes can be air that was left in the hose, so clear the air and repeat. A restart every ten or twenty seconds is a real leak, and a restart every few seconds means the pump is badly worn or a valve is being held open by debris.

4. Finding an Internal Leak

If the leak is inside the pump, there are three candidates. Graco's charts for its piston pumps separate them by stroke, and the logic is the same on every Graco pump of this design.

What you noticeLikely cause
Delivery is weak on the upstrokePiston ball check not seating, or piston packings worn
Delivery is weak on the downstroke, or on both strokesPiston packings worn, or the intake valve ball check not seating
Paint collects at the top of the pumpThroat packings worn

Work from cheap to costly.

  • Clean the intake valve. Debris holding the ball off its seat is common and free to fix. See how to clean or replace a Graco intake valve. The seat kit is 246429.
  • Then look at the piston valve and packings. If the intake valve is clean and the pump still will not hold, it needs a repack. Kit 18B260 covers the 246428 and 17C487 pump families and includes both check balls.
  • Keep the TSL topped up in the meantime. It protects the throat packings while you wait for parts. The 4 oz bottle is 238049.

5. When the Result Is Low Stall Pressure

A pump that holds pressure but stops too soon is being told to stop too soon. The fix depends on which control the sprayer has.

Sprayer familyGraco's remedy for low stall pressure
390 Classic, 190, RentalPro 210Turn the knob fully clockwise. If stall pressure is still low, replace the pressure control assembly
395, 490, 495, 595, 650Make sure the knob is installed so it can reach full clockwise. If the problem persists, replace the pressure transducer
Magnum-class sprayersIf the motor stops before the sprayer reaches the correct pressure, replace the pressure control switch

On SmartControl models you can confirm it with a pressure gauge in the hose. Graco's own flow chart for control faults starts by plumbing a gauge into the paint hose and reading what the sprayer actually reaches. The repairs are in how to test and replace a pressure transducer, how to replace a pressure control assembly and how to test a Magnum pressure control switch.

6. The Magnum Version

Graco's repair manual for Magnum-class sprayers gives its own short version of the test, and it uses paint.

  • Prime the sprayer with paint.
  • Turn the Prime/Spray valve to SPRAY and the pressure control fully clockwise.
  • Trigger the gun briefly.
  • When the trigger is released, the pump should cycle momentarily and stop.

If the pump continues to cycle, the manual says the pump valves may be worn or obstructed. The kits are 16E844 for the inlet and 16E845 for the outlet on the X5, X7, LTS 15 and LTS 17 platform, and the repair is in Magnum inlet and outlet valve replacement. The manual also lists a Prime/Spray valve leaking out of the drain line in the SPRAY position, so check the drain tube on a Magnum too.

7. When to Run It

  • Every 1000 gallons. That is Graco's interval for its contractor electric sprayers.
  • Before a big job. Five minutes in the shop beats an afternoon on site.
  • After any pump repair. It confirms the repack or valve work is sealed.
  • When the motor seems to run more than it used to. That is the early sign.
  • Before you buy a used sprayer. A seller who will not let you close the gun and wait two minutes is telling you something.
  • At the start of each season, after the storage fluid has been flushed out.

8. After the Test

Switch the sprayer off. Turn the prime valve to PRIME, trigger the gun into the pail and set the lock. Do not leave a sprayer sitting at pressure. If you are putting it away, finish with storage fluid as described in our winterizing guide.

Note the result somewhere. A pump that passed in spring and restarts every thirty seconds in autumn is telling you how fast it is wearing, and when to have the kit on the shelf.

Manuals with the maintenance tables for each model are in our manuals library.

Failed the Stall Test and Not Sure What to Order?

Tell us the model and what the pump did during the test, and we will help you pick the right kit.

Ask Our Parts Team Call +1 713-931-4102

Parts a Failed Stall Test Points To

Graco 18B260 Pump Packing Kit for Graco 290 to 595 Sprayers −30%
Graco
Graco 18B260 Pump Packing Kit for Graco 290 to 595 Sprayers
Part #: 18B260
(1)
$74.62 $106.00 Save $31.38
Buy Now
Graco 246429 Inlet Valve and Carbide Seat Kit −8%
Graco
Graco 246429 Inlet Valve and Carbide Seat Kit
Part #: 246429
(1)
$56.63 $61.75 Save $5.12
Buy Now
Graco 235014 Prime Drain Valve Spray Kit −23%
Graco
Graco 235014 Prime Drain Valve Spray Kit
Part #: 235014
(1)
$92.93 $121.00 Save $28.07
Buy Now
Graco 239914 Drain Valve Kit −10%
Graco
Graco 239914 Drain Valve Kit
Part #: 239914
(1)
$110.21 $123.00 Save $12.79
Buy Now
Graco 243222 Pressure Transducer −13%
Graco
Graco 243222 Pressure Transducer
Part #: 243222
(1)
$148.31 $169.50 Save $21.19
Buy Now
Graco 16E844 Pump Inlet Valve Repair Kit −8%
Graco
Graco 16E844 Pump Inlet Valve Repair Kit
Part #: 16E844
(1)
$59.15 $64.50 Save $5.35
Buy Now
Graco 16E845 Pump Outlet Valve Repair Kit −8%
Graco
Graco 16E845 Pump Outlet Valve Repair Kit
Part #: 16E845
(1)
$55.68 $60.25 Save $4.57
Buy Now
Graco 238049 Throat Seal Liquid - 4 oz (TSL) Genuine OEM
Graco
Graco 238049 Throat Seal Liquid - 4 oz (TSL)
Part #: 238049
(1)
$12.26
Buy Now

10. Frequently Asked Questions

What is a stall test on an airless sprayer?

It is a check of whether the sprayer holds pressure with the gun closed. You prime it, bring it to pressure and release the trigger. The motor should stop, or stall, and not restart until you pull the trigger again.

How often should I do a stall test on a Graco sprayer?

Graco's maintenance table for its 490 to 650 PC sprayers lists the stall check every 1000 gallons. It is also worth doing before a large job, after any pump repair and whenever the motor seems to run more than usual.

What does it mean if my sprayer will not stall?

Pressure is leaking somewhere. Graco says to inspect the pump for internal and external leaks and to check the prime valve for leaks. The usual causes are a leaking prime valve, a dirty or worn intake valve, a worn piston valve or worn piston packings.

What is low stall pressure?

It is when the sprayer stops the motor before reaching full pressure, even with the control turned fully clockwise. Graco's remedy is the pressure control assembly on 390-class sprayers, the pressure transducer on SmartControl models and the pressure control switch on Magnum-class sprayers.

Can I do a stall test with paint instead of water?

Yes, and Graco's Magnum procedure uses paint. Water is useful on a contractor sprayer because it is thinner and shows a small leak more readily, and it makes the cleanup easier.

Does a failed stall test mean I need a new pump?

Not usually. Start with the prime valve and the intake valve, which are inexpensive to clean or replace. If those are good, a packing kit normally restores the pump. A new pump is needed when the rod or cylinder is worn.

On this page
Your Cart
No items in cart.
Add more items
Total 0
Checkout Modify Cart